CABLE TYPES AND FEATURES:

Ücretsiz Forex Kitabı Kazanmak için tıklayın
       Cables, TS (Turkish Standards), VDE (German standard), IEC (International Electrical Comission), BS (British Standard) are classified according to the symbols. Turkey is a case-by area of ​​use is a cable standard, N cable, Y cable. Then it continues with letters and numbers indicating the contents of the cable. For example, NYY, as YVV. Common cable types used in the major study together.


N Cables (TS):
Hard as a surface-mounted and used under the plaster. Normal operating conditions and light-fired power plants.

   
 1-solid or stranded copper conductor
 2-Protodur insulator

3-Fill
4-Protodur coat (jacket)

Solid or stranded copper conductor, single or multi-core PROTODUR (PVC-based thermoplastic custom) insulation and PROTODUR low voltage cable sheath. Routed under the ground. Several cross-section and are stranded, 1,5 - 2,5 - 4 - 6-10 - 16 mm ² cross section, and 2,3,4-core standard is produced.


Y Cables (TS):
Energy, power and lighting, control (power plants, etc.). Outward as cable, cable ducts, under ground and salty water if specially produced is used. Resistant cable is used for fixed installations and severe operating conditions.






YE3SV Cable



1-Copper conductor
2-semiconductor layer
3-x insulator Protothen
4-semiconductor crepe paper
 5-copper wire screen
 6-Protection Tape
 7-Protodur outer sheath
                                                                  
Stranded copper conductor, dielectric losses are very small Protothen-x (by applying various methods of pure polyethylene, thermo-insulating improved mechanical properties) insulation. Special inner and outer semi-conductive layers, high short-circuit on conductor and insulation, copper wire screen, Protodur outer sheath medium voltage energy cables
(E3-cross-linked polyethylene, S-trench, with V-PVC thermoplastic insulator or sheath)




YSLTK-JZ (VDE) Cable

 1-bearing element
 2-rubber grips
 3-Protodur numbered  veins
 4-Separators
 5-Textile mesh
 6-cold-resistant outer sheath Protodur

Fine stranded copper conductor, Protodur, numbered cores, rubber sheath over the carrier element, dry, steam and wet areas, elevator, crane and cables used in marching band facilities. Standard cross-section 1 mm ² x (7, 12, 18, 24, 30 core) are carried out.



H Cables

Closed and dry areas, fixed installations and mobile device connections, is used on and under plaster.



HO5V-U cable

1-a stranded copper conductor                                                 
2-Protodur insulator

Closed and dry areas, fixed installations, distribution boards contacts they, in and under plaster on the pipes, hooks used on the cable core. Standard sections 0.5 to 0.75 - 1 mm ². The permissible operating temperature of 70 º C (meanings of the letters H-harmonized type, 05 to 300 and 500 Volt voltage, V-PVC insulation, U-Tek wire).



H03VV-F - a symbol of the old TS FVV Cable

1-Fine-stranded copper conductor                                       
2-Protodur insulator 
3-Protodur outer sheath

Mechanical stress is less closed and dry areas, cable is used as the moving contact. Fine stranded copper conductor Protodur insulation and Protodur outer sheath of flexible cables. Standard cross-section 0.50 mm ² x (2, 3 or 4-core) - 0.75 mm ² x (2, 3 or 4-core) are performed (H-harmonized type, 03 to 300 volts, V-PVC insulation, F-flexible fine wire).





H05RR-F Cable


1-Tinned conductor                         
2-rubber insulation
3-rubber grips

Tinned, finely stranded copper conductor rubber insulated, multi-core, industrial grade rubber sheathed cables. In damp places, water heaters, electric cookers, portable workshop tools such as hand drills and electric hand lamps, are used where mechanical effects. Standard cross-section 0.75 - 1 - 1,5 - 2,5 - 4 mm ² x (2, 3 or 4 wire) made ​​in (H-harmonized type, 05 to 300/500 V voltage, R-stranded, the F-flexible fine wire).


H05VV5-F Cable

Fine stranded copper conductor, Protodur, numbered cores, and flexibl
control, measurement and control cables. Where there is no mechanical stress, control equipments, and computer systems. Standard cross-section 0.75 mm ² x is the number of the various vessels.